mslu300 series dc/dc converter 1w, high isolation,smd-package e-mail:sales@minmax.com.tw tel:886-6-2923150 2011/12/15 rev:8 page 1 of 4 features ? smd package with industry standard pinout ? small footprint: 11.0x 16.3 mm (0.43?x 0.64?) ? high 3000vdc i/o-isolation ? single and dual output models ? operating temp. range ?40c to +85c ? high accuracy of pin planarity ? qualified for lead-free reflow solder process according ipc/jedec j-std-020d ? tape & reel package available ? 3 year product warranty product overview the minmax mslu300 series is a range of 1w dc/dc converters in a smd- package featuri ng high i/o-isolation of 3000vdc.the very small footprint makes this product the ideal solution for many applications whe re a voltage has to be isolated i.e for noise reduction, ground loop elimination,in digital interfaces or where a conv erted voltage is required. an excellent efficiency allows an operating temperature range of ?40c to +85c. with a new package design these converters are fully qualified for the higher temperature profile used in lead-free reflow solder processe s. for automated smd production lines the product can be sup plied in tape& reel package. model selection guide output current input current efficiency (typ.) input voltage (range) output voltage max. min. @max. load @no load load regulation max. capacitive load @max. load model number vdc vdc ma ma ma(typ.) ma(typ.) % (max.) uf % MSLU301 3.3 260 5 238 10 33 72 mslu302 5 200 4 267 10 33 75 mslu304 12 84 2 255 7 4.7 79 mslu305 15 67 1.5 251 7 4.7 80 mslu306 5 100 2 267 10 10# 75 mslu308 12 42 0.8 255 7 2.2# 79 mslu309 5 (4.5 ~ 5.5) 15 34 0.7 255 30 7 2.2# 80 mslu311 3.3 260 5 98 10 33 73 mslu312 5 200 4 110 8 33 76 mslu314 12 84 2 105 5 4.7 80 mslu315 15 67 1.5 103 5 4.7 81 mslu316 5 100 2 110 8 10# 76 mslu318 12 42 0.8 105 5 2.2# 80 mslu319 12 (10.8 ~ 13.2) 15 34 0.7 106 15 5 2.2# 80 mslu321 3.3 260 5 51 10 33 70 mslu322 5 200 4 57 8 33 73 mslu324 12 84 2 53 5 4.7 79 mslu325 15 67 1.5 53 5 4.7 79 mslu326 5 100 2 57 8 10# 73 mslu328 12 42 0.8 53 5 2.2# 79 mslu329 24 (21.6 ~ 26.4) 15 34 0.7 54 8 5 2.2# 79 # for each output input specifications parameter model min. typ. max. unit 5v input models 4.5 5 5.5 12v input models 10.8 12 13.2 input voltage range 24v input models 21.6 24 26.4 5v input models -0.7 --- 9 12v input models -0.7 --- 18 input surge voltage (1 sec. max.) 24v input models -0.7 --- 30 vdc reverse polarity input current --- --- 0.3 a input filter internal capacitor internal power dissipation all models --- --- 550 mw
mslu300 series dc/dc converter 1w, high isolation,smd-package e-mail:sales@minmax.com.tw tel:886-6-2923150 2011/12/15 rev:8 page 2 of 4 output specifications parameter conditions min. typ. max. unit output voltage balance dual output, balanced loads --- 0.1 1.0 % line regulation for vin change of 1% --- 1.2 1.5 % load regulation io=20% to 100% see model selection guide ripple & noise (20mhz) --- 75 100 mv p-p ripple & noise (20mhz) over line, load & temp. --- --- 150 mv p-p ripple & noise (20mhz) --- --- 15 mv rms temperature coefficient --- 0.01 0.02 %/ short circuit protection 0.5 second max. general specifications parameter conditions min. typ. max. unit i/o isolation voltage (rated) 60 seconds 3000 --- --- vdc i/o isolation resistance 500 vdc 10 --- --- g ? i/o isolation capacitance 100khz, 1v --- 60 100 pf switching frequency 50 100 150 khz mtbf (calculated) mil-hdbk-217f@25 , ground benign 2,000,000 --- --- hours moisture sensitivity level (msl) ipc/jedec j-std-020d level 2 input fuse 5v input models 12v input models 24v input models 500ma slow-blow type 200ma slow-blow type 100ma slow-blow type environmental specifications parameter conditions min. max. unit operating temperature range (with derating) ambient -40 +85 case temperature --- +90 storage temperature range -50 +125 humidity (non condensing) --- 95 % rel. h cooling free-air convection lead temperature (1.5mm from case for 10sec.) --- 300 output voltage tolerance (3.3v & 5v output) (all other output) 0% 20% 40% 60% 80% 100% output voltage(%) output load current (%) m a x . t y p . +5% +10% +15% vnom -5% -10% +20% +5% +10% +15% vnom -5% -10% +20% m in . 0% 20% 40% 60% 80% 100% output voltage(%) output load current (%) m a x . t y p . +5% +10% +15% vnom -5% -10% +20% +5% +10% +15% vnom -5% -10% +20% m i n .
mslu300 series dc/dc converter 1w, high isolation,smd-package e-mail:sales@minmax.com.tw tel:886-6-2923150 2011/12/15 rev:8 page 3 of 4 power derating curve notes 1 specifications typical at ta=+25 , resistive load, nominal input voltage and ra ted output current unless otherwise noted. 2 ripple & noise measurement bandwidth is 0-20mhz. 3 these power converters require a minimu m output loading to maintain specified re gulation, operation u nder no-load conditions will not damage these modules; however they may not meet all specifications listed. 4 all dc/dc converters should be externally fused at the front end for protection. 5 other input and output voltage may be av ailable, please contact factory. 6 that ?natural convection? is about 20lfm but is not equal to still air (0 lfm). 7 specifications subject to change without notice. 8 it is not recommended to use water-washing process on smt units. package specifications mechanical dimensions connecting pin patterns ? all dimensions in mm (inches) ? tolerance: x.x0.25 (x.xx0.01) x.xx0.13 ( x.xxx0.005) ? pins 0.05 (0.002) pin connections physical characteristics pin single output dual output case size : 16.3x8.0x7.7mm (0.64x0.31x0.30 inches) 1 -vin -vin 2 +vin +vin case material : non-conductive bl ack plastic (flammability to ul 94v-0 rated) 3 na na 5 -vout common weight : 2g 6 na -vout 7 na na 8 +vout +vout 10 na na 11 na na 12 na na na : not available for electrical connection 123 5 12 11 10 8 6 7 8.0 [0.31] 0.60 [0.02] 16.3 [0.64] 8.0 0.5 [0.31 0.02] 0.3 [0.01] 11.0 0.2 [0.43 0.008] 7.7 [0.3] 1.8 [0.07] 5.08 5.08 [0.2] [0.2] 1.5 0.1 5.5 [0.06 0.004] [0.22] 1.5 0.1 [0.06 0.004] 5.5 [0.22] s seating plane 2.54 [0.1] 0 ~ 4 0.25 [0.01] r 0 . 5 ( magnification of a ) 0.1 s 10.6 [0.42] 12.70 [0.50] 1.7 [0.07] 2.54 [0.10] 1.0 [0.04] 5.08 [0.20]
mslu300 series dc/dc converter 1w, high isolation,smd-package 18, sin sin road, an-ping industr ial district, tainan 702, taiwan tel: 886-6-2923150 fax: 886-6-2923149 e-mail: sales@minmax.com.tw 2011/12/15 rev:8 page 4 of 4 minmax technology co., ltd. test configurations peak-to-peak output noise measurement test use a cout 0.33uf ceramic capacitor. scope measurement should be made by using a bnc socket, measurement bandwidth is 0-20 mhz. position the load between 50 mm and 75 mm from the dc/dc converter. +out -out +vin -vin single output dc / dc converter resistive load scope copper strip cout copper strip +out -out +vin -vin dual output dc / dc converter resistive load scope copper strip cout com. scope cout copper strip copper strip design & feature considerations maximum capacitive load the mslu300 series has limitation of maximum connected capacitanc e at the output. the power module may be operated in current l imiting mode during start-up, affecting the ramp-up and the startup time. the maximum capacitance can be found in the data sheet. input source impedance the power module should be connected to a lo w ac-impedance input source. highly inductive source impedances can affect the stab ility of the power module. in applications where power is supplied ov er long lines and output loading is high, it may be necessary to use a capacitor at t he input to ensure startup. capacitor mounted close to the power module helps ensure stabilit y of the unit, it is recommended to use a good quality low equ ivalent series resistance (esr < 1.0 ? at 100 khz) capacitor of a 2.2uf for the 5v input devices, a 1.0uf for the 12v input devices and a 0.47uf for the 24v devices. + +out -out +vin -vin dc / dc converter load dc power source + - cin output ripple reduction a good quality low esr capacitor placed as close as practicable across the load will give the best ripple and noise performance . to reduce output ripple, it is recommended to use 1.0uf capacitors at the output. +out -out +vin -vin load dc power source + - cout single output dc / dc converter +out -out +vin -vin load dc power source + - cout com. dual output dc / dc converter load cout thermal considerations many conditions affect the thermal perform ance of the power module, such as orient ation, airflow over the module and board spac ing. to avoid exceeding the maximum temperature rating of the components inside the power module, the case temperature must be kept below 90 . the derating curves are determined from measurements obtained in a test setup. dut position of air velocity probe and thermocouple 50mm / 2in air flow 15mm / 0.6in
|
